第一種方式：機械夾裝

    該方式主要用于形狀規則的薄型工件，借助平面磨床工作臺磁性作用吸附磨床附帶的平口鉗，利用平口鉗固定工件。采用進給量逐漸減少的辦法磨平薄片工件一平面后取下，這時把已磨好的一平面放到磁性工作臺上，再進行磨削薄片工件的另一平面，反復磨削幾次，兩平面的平面度達到要求。

第二種方式：真空夾裝

   該法利用氣壓原理固定較薄形狀規則工件。在裝夾工件的專用夾具上安裝密封圈，用密封圈固定工件，兩者之間形成一各密閉的空腔，采用吸泵將空腔內的氣體抽出，利用氣壓差夾緊工件。當

第三種：化學結合劑法

   可以運用化學結合劑，如常用的環氧樹脂結合劑，將工件與合適的可以吸磁的平面粘合在一起，利用平面的磁性固定于圓臺平面磨床電磁吸盤上進行磨削，磨平薄片一端平面后，再將薄片工件從平板上取下來，以磨平的一面放到磁力吸盤上，再磨削薄片工件的另一端平面

第四種：彈墊夾裝

  在平面磨床上磨削上述薄片工件時，采用彈性夾緊機構，使薄片工件在自由狀態下實現定位與夾緊。在工件與磁性工作臺之間墊一層0.5mm厚的橡膠，當工件受磁性吸引力作用時，橡膠被壓縮，彈性變形變小，從而可磨削出工件的平直平面。反復磨削幾次，可滿足加工精度要求。